EV Charger Breaker Size Chart - 16 to 80 Amps, Wire Included
Every EV charger setting has a matched breaker and wire, set by one rule: charging is a continuous load, so the circuit is sized at 125 percent of the charger setting. This chart runs settings from 16 to 80 amps through that rule, then covers the plug-in ceiling and the panel capacity question.
Built to NEC 2023 tables. No reviewer claim until a licensed reviewer is signed.
The chart
Breaker is the next standard 240.6 rating at or above 125 percent of the charger setting. Wire is the smallest copper conductor whose Table 310.16 ampacity at 75 C reaches the breaker rating, with the 240.4(D) small-conductor caps applied.
| Charger setting | Breaker (125 percent) | Copper wire |
|---|---|---|
| 16 A | 20 A | 12 AWG |
| 24 A | 30 A | 10 AWG |
| 32 A | 40 A | 8 AWG |
| 40 A | 50 A | 8 AWG |
| 48 A | 60 A | 6 AWG |
| 64 A | 80 A | 4 AWG |
| 80 A | 100 A | 3 AWG |
Two rows show the rules working. At 16 A the wire is 12 AWG, not 14 AWG: 14 AWG copper has the ampacity for a 20 A circuit on paper, but 240.4(D) caps its protection at 15 A, so the chart steps up. At 40 A the breaker lands on 50 A and the wire stays at 8 AWG, because 8 AWG copper carries exactly 50 A at 75 C; one setting higher, at 48 A, the 60 A breaker outruns it and the wire moves to 6 AWG. The EV charger load calculator runs the same construction for any setting, including the voltage drop on the run to a detached garage.
How the rule works
Article 625 treats EV charging as a continuous load, and 625.41 and 625.42 put the branch circuit, conductors and breaker alike, at 125 percent of the charger's rating. The reasoning is duration: a charger at full setting runs for hours at a stretch, overnight, at exactly its rated current, which is the duty the continuous rule exists for. The figure to size from is the charger's configured output, not the car's maximum acceptance and not the charger's highest possible setting. Most wall units are adjustable at installation, by switch, dial or app, precisely so the circuit and the setting can be matched to what the panel can give. A unit set to 32 A is a 32 A load for sizing, whatever it could be set to later; raising the setting later is an electrical change, not a preference, and the circuit has to be rechecked when it happens.
Hardwired vs plug-in: the 14-50 ceiling
Plug-in charging tops out lower than hardwired charging, and the chart's middle row is the boundary. The standard receptacle for EV charging is the NEMA 14-50 on a 50 A circuit, and a receptacle circuit may not be loaded continuously beyond 80 percent of its rating, which puts the plug-in ceiling at 40 A of charging. Settings of 48 A and above are hardwired territory: no receptacle, the unit connected directly, on the 60 A and larger circuits from the chart. Plug-in brings one more constraint worth knowing before the parts are bought: the receptacle itself must be rated for the circuit, an industrial-grade 14-50 is the durable choice for a device that will be plugged and unplugged across years of daily cycles, and the installation instructions for the charger, which carry the force of the listing under 110.3(B), may specify the circuit arrangement outright. The breaker size calculator covers the same 125 percent construction for continuous loads generally.
What each setting actually delivers
The setting is a current; the car experiences a power. At 240 V the chart's rows deliver 3.84 kW at 16 A, 5.76 kW at 24 A, 7.68 kW at 32 A, 9.6 kW at 40 A, 11.52 kW at 48 A, 15.36 kW at 64 A and 19.2 kW at 80 A. How far that power goes depends on the vehicle, but the overnight arithmetic is setting-driven: across an eight-hour night the 32 A row delivers about 61 kWh and the 48 A row about 92 kWh, against the battery capacity of the car being charged. For a household whose daily driving uses a fraction of the pack, the middle rows refill it with hours to spare, which is why the jump from 40 A to 48 A charging is so often bought for a circuit and panel strain it does not need. Cars supplied at 208 V, common in some townhouse and condo services, draw the same settings at lower power, 32 A delivering about 6.7 kW, another reason the setting on the unit, not the brochure figure, is the number to plan around.
Two chargers change the picture once more. Paired units from most makers offer power sharing: a group setting caps their combined draw, and the pair divides it as the cars demand, so two vehicles can share one chart row's worth of circuit instead of needing two. Article 625 recognises the arrangement through the energy management provisions, and the load calculation takes the managed total rather than the sum of the nameplates. It is frequently the difference between charging two cars on a 100 A service and upgrading the service to charge them, and it belongs in the plan before the first circuit is run, not after the second car arrives.
The panel capacity question
A circuit that fits the charger does not automatically fit the service. A 60 A charging circuit is a minor addition to a 200 A service with headroom and a serious one to a 100 A service already carrying electric heat, a range and a dryer. Article 220 answers with arithmetic, not impressions: the charger enters the dwelling load calculation at 125 percent of its setting, as this site's EV tool notes, and it is the single most common reason an older 100 A service stops calculating. Where the total lands over the line, the honest options are a lower charger setting, which the adjustability exists to allow, a load management device that pauses charging under the service's peaks, or a service upgrade sized by the same calculation. The dwelling load calculator runs the total with the charger in its place, so the decision comes from the numbers rather than from a tripping main breaker at midnight.
Planning only
This guide is a planning reference built on NEC 2023 methods. Charger installation is permit work in most jurisdictions, the manufacturer's instructions govern the specific unit, and the final selection for a real installation belongs with your authority having jurisdiction and your licensed electrician.