What Size Breaker for a Dryer - the 30 Amp Standard and Its Exceptions
Almost every full-size electric dryer lands on the same circuit: a 30 A breaker and 10 AWG wire. This guide covers why that is the standard, the nameplate check that can change it, and the 3-wire versus 4-wire receptacle question that comes with any dryer circuit.
Built to NEC 2023 tables. No reviewer claim until a licensed reviewer is signed.
Why 30 A and 10 AWG is the default
Full-size residential dryers are built to a shared pattern: a heating element in the 5,000 W class and a small drum motor, with typical nameplates rating the appliance around 22 to 24 A at 240 V. The industry settled on a 30 A branch circuit for that load a generation ago, and the receptacle, the cord and the breaker all standardised around it. The conductor follows from the table: 10 AWG copper carries 35 A at 75 C, and 240.4(D) caps its protection at exactly 30 A, so 10 AWG and the 30 A breaker are a matched pair with nothing left over and nothing missing. The receptacle is a NEMA 14-30, rated 30 A at 250 V, and the circuit is dedicated: one dryer, one circuit.
Note what the 30 A figure is not. It is not a continuous-load calculation of the water heater kind, and it is not the dryer's demand figure in a service calculation. It is the branch-circuit rating the appliance's listing and instructions are written around, which is why it survives every variation in element wattage inside the standard class. The breaker size calculator covers the general method for loads that do not arrive with a standard attached; the dryer is the case where the standard came first.
The nameplate check
The default has edges, and the nameplate finds them. Before wiring anything, read the rating plate for the appliance's rated current and any stated circuit requirement, because manufacturer instructions carry the force of the listing under 110.3(B). Three variations account for nearly every exception.
Compact and apartment-size dryers are the commonest. Many are 120 V appliances drawing in the low teens of amps, sold for a standard 15 or 20 A receptacle circuit, and putting one on a 30 A circuit because "dryers take 30 A" would leave it protected far above its design. At the other edge, a small number of large or commercial-pattern dryers nameplate above the standard class and specify a larger circuit in their instructions; the instruction figure governs. Gas dryers close the list: the drum motor, controls and igniter are the only electrical loads, and they run on an ordinary 120 V receptacle circuit, with the gas line doing the heating work. In every variation the pattern is the same: the standard fills the silence, and the nameplate overrules it.
The other 5,000 W figure: dryers in a load calculation
One confusion follows this appliance into service work. NEC 220.54 lets a load calculation count household dryers at 5,000 W or the nameplate rating, whichever is larger, and applies demand factors when four or more dryers share a service. That 5,000 W is a demand figure for sizing services and feeders; it is not the branch-circuit answer, and it does not shrink the dryer's own circuit below the 30 A standard. The two numbers coexist because they answer different questions: the calculation asks what the service will actually see with everything diversified, the branch circuit asks what this appliance may draw through its own breaker on its worst day. Keeping them separate is most of residential load work, and the wire size calculator handles the conductor side of both, from the branch run to the feeder.
Not the laundry circuit
One neighbouring rule causes regular confusion in laundry rooms. The 20 A laundry branch circuit required by 210.11(C)(2) serves the washer and the laundry receptacles; it is a separate circuit from the dryer's 30 A circuit, and the two are not interchangeable or shareable. A gas dryer plugs into the laundry circuit alongside the washer, because its electrical load is only a motor and controls. An electric dryer's dedicated 30 A circuit serves the dryer alone. Remodels that find both appliances improvised onto one circuit are finding two circuits' worth of load on one circuit's protection.
Three wires or four
Older dryer circuits were wired with three conductors and a NEMA 10-30 receptacle, using the neutral as both the return path and the grounding path for the appliance frame. That arrangement was permitted for decades and survives under 250.140 only as an exception for existing installations that meet its conditions, including an insulated neutral, or one covered where the rules allow, and a supply from the service or a qualifying separately derived source. New work is four-wire: two ungrounded conductors, an insulated neutral, and a separate equipment grounding conductor, landing on a 14-30 receptacle, with the dryer's frame bonded to the ground and never to the neutral.
The practical moment this matters is a dryer replacement in an older home. The new appliance arrives with instructions for both cord types, and the correct cord is the one matching the receptacle and the circuit behind it: a 4-wire cord on a 4-wire circuit, with the dryer's internal bonding strap removed, and a 3-wire cord only where the existing circuit qualifies for the exception, with the strap in place. Changing the receptacle without changing the circuit, or the cord without checking the strap, is how frames end up carrying neutral current. When a kitchen or laundry renovation touches the circuit, bringing it to four wires is the durable answer.
Planning only
This guide is a planning reference built on NEC 2023 methods. The manufacturer's instructions govern the specific appliance, local amendments vary, and the final selection for a real installation belongs with your authority having jurisdiction and your licensed electrician.