What Size Breaker for a Stove or Range - Demand Factors Explained

Most home ranges land on a 40 A or 50 A breaker, and the nameplate, which can read 12 kW or more, is not the number that decides it. Table 220.55 demand factors do the deciding; this guide works the split and the wire that goes with each breaker.

Built to NEC 2023 tables. No reviewer claim until a licensed reviewer is signed.

The 40 A and 50 A split

Start with the answer by range size. A single household range rated up to 12 kW, which covers the great majority of freestanding ranges sold for homes, takes a demand of 8 kW under Table 220.55, and 8,000 W at 240 V is 33.3 A. The branch circuit is therefore a 40 A breaker, which is also the code floor for this appliance class: ranges rated over 8.75 kW require a branch circuit of not less than 40 A. Larger ranges move the demand, not by their full nameplate, but by the table's growth rule: 5 percent more demand for each kilowatt of rating above 12 kW. A 16 kW range, a big double-oven model, demands 8 kW times 1.20, which is 9.6 kW, or 40.0 A at 240 V: still a 40 A minimum on the arithmetic, and the case where most installers choose a 50 A breaker and the heavier wire, because the calculation lands exactly on the rating with nothing in reserve. The breaker size calculator runs the general sequence behind these answers for loads that arrive without a demand table.

Table 220.55 in plain terms

The demand factor is not a fudge; it is a measurement of how ranges are actually used. A range nameplate sums every element at full power: four burners, the oven element, the broiler. In service, elements cycle on their thermostats, the oven holds temperature at a fraction of its element rating, and nobody runs every surface unit at maximum while broiling. Table 220.55 Column C encodes that behaviour: one range up to 12 kW counts as 8 kW of demand, and the counted share falls further as more ranges share a service, which is why apartment buildings are not wired for the sum of their kitchens.

Two boundaries matter. The table applies to household cooking equipment; a commercial range in a restaurant kitchen is a different load with different rules. And the demand figure is a sizing permission, not a prediction: it says the circuit built to it will not be overloaded by the appliance's real duty, not that the range can never draw more in a single moment. Breakers tolerate the brief excursions; the conductor sizing is built on the demand the table assigns.

The wire that goes with each breaker

For a 40 A breaker, the conductor is 8 AWG copper, 50 A at 75 C, or 6 AWG aluminum at the same 50 A. For a 50 A breaker, the standard choice is 6 AWG copper, 65 A at 75 C. One cable type changes the reading: NM cable is limited to the 60 C column by 334.80, where 8 AWG copper carries 40 A and 6 AWG copper carries 55 A. An 8 AWG NM run therefore tops out at the 40 A circuit, and a 50 A range circuit wired in NM needs 6 AWG regardless of what the 75 C column allows for other wiring methods. Receptacle circuits land on a NEMA 14-50; hardwired cooktops and wall ovens follow their own nameplates, and a separate cooktop and oven on one circuit are combined under the table's notes, treated as a single range of their summed rating for the demand figure. The wire size calculator applies the temperature column and the drop check to whichever run you are planning.

Separate cooktop and wall oven

The built-in kitchen splits the appliance in two, and the table has a note for it. Under the notes to Table 220.55, a counter-mounted cooktop and up to two wall ovens fed from a single branch circuit are added together and treated as one range, so the demand figure comes from their summed rating exactly as if one appliance carried it. Worked: a 7.8 kW cooktop and a 4.2 kW wall oven sum to 12.0 kW, which takes the Column C demand of 8 kW, or 33.3 A, and lands on the same 40 A circuit as a freestanding range of the same total. Fed separately, each appliance follows its own nameplate and instructions instead, and many cooktops arrive specifying a 40 A or 50 A circuit outright; where the instruction sheet names the circuit, it governs over the table, under the same 110.3(B) principle as every other appliance on this site. The trap is mixing the two systems, summing the nameplates for one decision and applying the demand table for another. Pick the arrangement the kitchen is actually wired as, then let one method carry the whole calculation.

The demand figure's second job

The 8 kW from Table 220.55 does double duty: it is also the figure a dwelling load calculation takes for the range when sizing the service. That is the connection between this guide and the service question. A house whose range counts 8 kW, whose dryer counts 5 kW under its own rule, and whose water heater counts at full rating adds up very differently from the sum of the nameplates, and the difference is routinely the difference between a 100 A and a 200 A service. The dwelling load calculator runs that whole calculation with each appliance's demand rule applied in its place.

Planning only

This guide is a planning reference built on NEC 2023 methods. The manufacturer's instructions govern the specific appliance, local amendments vary, and the final selection for a real installation belongs with your authority having jurisdiction and your licensed electrician.